2022 China New Design Tap Aggregator - Mylinking™ Network Tap ML-TAP-2810 – Mylinking
2022 China New Design Tap Aggregator - Mylinking™ Network Tap ML-TAP-2810 – Mylinking Detail:
1- Overviews
- A full visual control of Data Acquisition device(4*10GE SFP+ plus 24*GE SFP ports)
- A full Data Scheduling Management of nework traffic capture and monitoring device(duplex Rx/Tx processing)
- A full packet pre-processing and re-distribution device(bidirectional bandwidth 64Gbps)
- Supported traffic collection & reception of link data from different network element locations
- Supported traffic collection & reception of link data from different switch routing nodes
- Supported raw packet captured, identified, analyzed, statistically summarized and marked
- Supported packet filtering matches, including policy filtering based on quintuple (source IP address, destination IP address, source port, destination port, and protocol number), packet characteristics, and deep identification of packet content
- Supported raw packet output for monitoring equipment of Data Packet Analysis, Protocol Analysis, Signaling Analysis, Security Analysis, Risk Management and other traffic reqirement.
ML-TAP-2810
2- System Block Diagram
3- Operating Principle
The Network Traffic Tap embedded traffic guidance function, which is mainly coordinated by the built-in TCAM traffic identification policy engine, traffic control guidance engine, port media transceiver module (MAC+PHY), and high-speed backplane switch bus. The port media transceiver module collects the traffic and enters the traffic identification matching engine to perform traffic identification matching. The identification matching engine performs high-speed hardware parallel matching based on the TCAM three-state content addressing memory, which can complete high-speed traffic identification of line speed traffic. After traffic identification, the traffic will enter the high-speed switching bus for traffic forwarding, replication, aggregation, or shunting. The traffic control guide engine can accurately control the traffic output interface of each type of traffic identification frame.
4- Intelligent Traffic Processing Abilities
6- Specifications
Mylinking™ Network Tap NPB/TAP Functional Parameters |
||
Network Interface | GE ports |
24*GE SFP slots |
10GE ports |
4*10GE SFP+ slots |
|
Deployment mode | SPAN monitoring input |
support |
In-line mode |
support |
|
Total QTYs interface |
28 |
|
Traffic replication / aggregation / distribution |
support |
|
Link QTYs supporting Mirror replication / aggregation |
1 -> N link traffic replication (N <28) N-> 1 link traffic aggregation (N <28) G Group(M-> N Link) traffic replication and aggregation [G * (M + N) <28] |
|
Functions |
Distribution based on traffic identification |
support |
Distribution based on IP / protocol / port Five tuple traffic identification |
support |
|
Distribution strategy based on protocol header the key labeled traffic identifies |
support |
|
Strategic distribution based on deep message content identification |
support |
|
Support Ethernet encapsulation independence |
support |
|
CONSOLE Network Management |
support |
|
IP/WEB Network Management |
support |
|
SNMP V1/V2C Network Management |
support |
|
TELNET/SSH Network Management |
support |
|
SYSLOG Protocol |
support |
|
User authentication function |
Password authentication based on user name |
|
Electric(1+1 Redundant Power System-RPS) |
Rated supply voltage |
AC110-240V/DC-48V [Optional] |
Rated power frequency |
AC-50HZ |
|
Rated input current |
AC-3A / DC-10A |
|
Rated power function |
150W(2401: 100W ) |
|
Environment |
Operating Temperature |
0-50℃ |
Storage Temperature |
-20-70℃ |
|
Operating Humidity |
10%-95%, Non-condensing |
|
User Configuration |
Console Configuration |
RS232 Interface, 9600,8,N,1 |
Password authentication |
support |
|
Rack Height |
Rack space (U) |
1U 460mm*45mm*440mm |
7- Order Information
ML-TAP-2401 mylinking™ Network Tap 24*GE SFP ports
ML-TAP-1410 mylinking™ Network Tap 12*GE SFP ports plus 2*10GE SFP+ ports
ML-TAP-2610 mylinking™ Network Tap 24*GE SFP ports plus 2*10GE SFP+ ports
ML-TAP-2810 mylinking™ Network Tap 24*GE SFP ports plus 4*10GE SFP+ ports
Product detail pictures:


Related Product Guide:
"Sincerity, Innovation, Rigorousness, and Efficiency" could be the persistent conception of our organization for your long-term to establish alongside one another with shoppers for mutual reciprocity and mutual benefit for 2022 China New Design Tap Aggregator - Mylinking™ Network Tap ML-TAP-2810 – Mylinking , The product will supply to all over the world, such as: Wellington, Russia, Las Vegas, We solution have passed through the national skilled certification and been well received in our key industry. Our specialist engineering team will often be ready to serve you for consultation and feedback. We've been able to also provide you with no cost samples to meet your needs. Best efforts are going to be produced to supply you the very best service and solutions. For anyone who is considering our business and solutions, please speak to us by sending us emails or get in touch with us right away. As a way to know our items and enterprise. lot more, you'll be able to come to our factory to find out it. We'll constantly welcome guests from around the globe to our firm. o build enterprise. elations with us. You should really feel absolutely free to make contact with us for small business and we believe we'll share the top trading practical experience with all our merchants.

The factory technical staff not only have high level of technology, their English level is also very good, this is a great help to technology communication.
