Bottom price Tap Adapter - Mylinking™ Network Tap ML-TAP-2810 – Mylinking
Bottom price Tap Adapter - Mylinking™ Network Tap ML-TAP-2810 – Mylinking Detail:
1- Overviews
- A full visual control of Data Acquisition device(4*10GE SFP+ plus 24*GE SFP ports)
- A full Data Scheduling Management of nework traffic capture and monitoring device(duplex Rx/Tx processing)
- A full packet pre-processing and re-distribution device(bidirectional bandwidth 64Gbps)
- Supported traffic collection & reception of link data from different network element locations
- Supported traffic collection & reception of link data from different switch routing nodes
- Supported raw packet captured, identified, analyzed, statistically summarized and marked
- Supported packet filtering matches, including policy filtering based on quintuple (source IP address, destination IP address, source port, destination port, and protocol number), packet characteristics, and deep identification of packet content
- Supported raw packet output for monitoring equipment of Data Packet Analysis, Protocol Analysis, Signaling Analysis, Security Analysis, Risk Management and other traffic reqirement.
ML-TAP-2810
2- System Block Diagram
3- Operating Principle
The Network Traffic Tap embedded traffic guidance function, which is mainly coordinated by the built-in TCAM traffic identification policy engine, traffic control guidance engine, port media transceiver module (MAC+PHY), and high-speed backplane switch bus. The port media transceiver module collects the traffic and enters the traffic identification matching engine to perform traffic identification matching. The identification matching engine performs high-speed hardware parallel matching based on the TCAM three-state content addressing memory, which can complete high-speed traffic identification of line speed traffic. After traffic identification, the traffic will enter the high-speed switching bus for traffic forwarding, replication, aggregation, or shunting. The traffic control guide engine can accurately control the traffic output interface of each type of traffic identification frame.
4- Intelligent Traffic Processing Abilities
6- Specifications
Mylinking™ Network Tap NPB/TAP Functional Parameters |
||
Network Interface | GE ports |
24*GE SFP slots |
10GE ports |
4*10GE SFP+ slots |
|
Deployment mode | SPAN monitoring input |
support |
In-line mode |
support |
|
Total QTYs interface |
28 |
|
Traffic replication / aggregation / distribution |
support |
|
Link QTYs supporting Mirror replication / aggregation |
1 -> N link traffic replication (N <28) N-> 1 link traffic aggregation (N <28) G Group(M-> N Link) traffic replication and aggregation [G * (M + N) <28] |
|
Functions |
Distribution based on traffic identification |
support |
Distribution based on IP / protocol / port Five tuple traffic identification |
support |
|
Distribution strategy based on protocol header the key labeled traffic identifies |
support |
|
Strategic distribution based on deep message content identification |
support |
|
Support Ethernet encapsulation independence |
support |
|
CONSOLE Network Management |
support |
|
IP/WEB Network Management |
support |
|
SNMP V1/V2C Network Management |
support |
|
TELNET/SSH Network Management |
support |
|
SYSLOG Protocol |
support |
|
User authentication function |
Password authentication based on user name |
|
Electric(1+1 Redundant Power System-RPS) |
Rated supply voltage |
AC110-240V/DC-48V [Optional] |
Rated power frequency |
AC-50HZ |
|
Rated input current |
AC-3A / DC-10A |
|
Rated power function |
150W(2401: 100W ) |
|
Environment |
Operating Temperature |
0-50℃ |
Storage Temperature |
-20-70℃ |
|
Operating Humidity |
10%-95%, Non-condensing |
|
User Configuration |
Console Configuration |
RS232 Interface, 9600,8,N,1 |
Password authentication |
support |
|
Rack Height |
Rack space (U) |
1U 460mm*45mm*440mm |
7- Order Information
ML-TAP-2401 mylinking™ Network Tap 24*GE SFP ports
ML-TAP-1410 mylinking™ Network Tap 12*GE SFP ports plus 2*10GE SFP+ ports
ML-TAP-2610 mylinking™ Network Tap 24*GE SFP ports plus 2*10GE SFP+ ports
ML-TAP-2810 mylinking™ Network Tap 24*GE SFP ports plus 4*10GE SFP+ ports
Product detail pictures:
Related Product Guide:
We are proud of the high customer satisfaction and wide acceptance due to our persistent pursuit of high quality both on product and service for Bottom price Tap Adapter - Mylinking™ Network Tap ML-TAP-2810 – Mylinking , The product will supply to all over the world, such as: South Africa , Ottawa , Frankfurt , As an experienced factory we also accept customized order and make it same as your picture or sample specifying specification and customer design packing. The main goal of the company is to live a satisfactory memory to all the customers,and establish a long term win-win business relationship. For more information,please contact us. And it's our great pleasure if you like to have a personally meeting in our office.
By Pearl from Mecca - 2018.07.12 12:19
The company account manager has a wealth of industry knowledge and experience, he could provide appropriate program according our needs and speak English fluently.
By jari dedenroth from South Korea - 2018.12.11 11:26