Factory directly Active Tap - Mylinking™ Network Tap ML-TAP-2610 – Mylinking
Factory directly Active Tap - Mylinking™ Network Tap ML-TAP-2610 – Mylinking Detail:
1- Overviews
- A full visibility control of network traffic collection device(2*10GE SFP+ plus 24*GE SFP ports)
- A full Data Scheduling Management device(duplex Rx/Tx processing)
- A full pre-processing and re-distribution device(bidirectional bandwidth 44Gbps)
- Supported collection & reception of link data from different network element locations
- Supported collection & reception of link data from different switch routing nodes
- Supported raw packet collected, identified, analyzed, statistically summarized and marked
- Supports LAN/WAN mode; Supports packet filtering and forwarding based on the source port, quintuple standard protocol domain, source/destination MAC address, IP fragment, transport layer port range, Ethernet type field, VLANID, MPLS label, and TCPFlag fixed offset feature.
- Supported port traffic aggregation, Hash diversion, load balancing, and filtering, flexibly meeting your network security and traffic analysis device deployment requirements.
- Supported automatically various tunneling protocols identification such as GTP / GRE / PPTP / L2TP / PPPOE. Regarding the user configuration, the traffic output strategy can be implemented according to the inner or outer layer of the tunnel
ML-TAP-2610
2- System Block Diagram
Mylinking™ ML-TAP-2610 Network Tap is ASIC dedicated chip pure hardware design, high-speed backplane switching bus bandwidth up to 44Gbps, can achieve complete line speed flow collection, convergence, filtering, shunt, replication and other functions; TCAM hardware policy matching mark engine module can complete the packet security policy matching and traffic classification mark under the state of line speed flow. The traffic steering engine can implement free port forwarding, replication and shunting actions of marked traffic.
3- Operating Principle
- The easy-to-use WEB configuration interface eliminates complex CLI configuration. Advanced users can use no more than five commands to configure the complex traffic replication in different ports.
- Status monitoring; Port status on the WEB UI displays the power supply, system status, interface rate, interface LINK status, and data packets sent and received by the port.
- Fully compatible with intrusion detection system, protocol analyzer, RMON probe, network audit system and other applications.
4- Intelligent Traffic Processing Abilities
6- Specifications
Mylinking™ Network Tap NPB/TAP Functional Parameters |
||
Network Interface |
GE ports |
24*GE SFP slots |
10GE ports |
2*10GE SFP+ slots |
|
Deployment mode |
SPAN monitoring input |
support |
In-line mode |
support |
|
Total QTYs interface |
26 |
|
Traffic replication / aggregation / distribution |
support |
|
Link QTYs supporting Mirror replication / aggregation |
1 -> N link traffic replication (N <26) |
|
N-> 1 link traffic aggregation (N <26) |
||
G Group(M-> N Link) traffic replication and aggregation [G * (M + N) <26] |
||
Functions |
Distribution based on traffic identification |
support |
Distribution based on IP / protocol / port Five tuple traffic identification |
support |
|
Distribution strategy based on protocol header the key labeled traffic identifies |
support |
|
Strategic distribution based on deep message content identification |
support |
|
Support Ethernet encapsulation independence |
support |
|
CONSOLE Network Management |
support |
|
IP/WEB Network Management |
support |
|
SNMP V1/V2C Network Management |
support |
|
TELNET/SSH Network Management |
support |
|
SYSLOG Protocol |
support |
|
User authentication function | Password authentication based on user name | |
Electric(1+1 Redundant Power System-RPS) |
Rated supply voltage |
AC110-240V/DC-48V [Optional] |
Rated power frequency |
AC-50HZ |
|
Rated input current |
AC-3A / DC-10A |
|
Rated power function |
150W(2401: 100W ) |
|
Environment |
Operating Temperature |
0-50℃ |
Storage Temperature |
-20-70℃ |
|
Operating Humidity |
10%-95%, Non-condensing |
|
User Configuration |
Console Configuration |
RS232 Interface, 9600,8,N,1 |
Password authentication |
support |
|
Rack Height |
Rack space (U) |
1U 460mm*45mm*440mm |
7- Order Information
ML-TAP-2401 mylinking™ Network Tap 24*GE SFP ports
ML-TAP-1410 mylinking™ Network Tap 12*GE SFP ports plus 2*10GE SFP+ ports
ML-TAP-2610 mylinking™ Network Tap 24*GE SFP ports plus 2*10GE SFP+ ports
ML-TAP-2810 mylinking™ Network Tap 24*GE SFP ports plus 4*10GE SFP+ ports
Product detail pictures:
Related Product Guide:
We know that we only thrive if we can guarantee our combined rate competiveness and good quality advantageous at the same time for Factory directly Active Tap - Mylinking™ Network Tap ML-TAP-2610 – Mylinking , The product will supply to all over the world, such as: Oslo , Israel , Durban , If you are for any reason unsure which product to select, do not hesitate to contact us and we are going to be delighted to advise and assist you. This way we are going to be providing you with all the knowledge needed to make the best choice. Our company strictly follows "Survive by good quality, Develop by keeping good credit. " operation policy. Welcome all the clients old and new to visit our company and talk about the business. We have been looking for more and more customers to create the glorious future.
By Victor Yanushkevich from Bolivia - 2017.12.31 14:53
We are old friends, the company's product quality has been always very good and this time the price is also very cheap.
By Fiona from Qatar - 2017.09.22 11:32