Manufacturer of Data Center Tap - Mylinking™ Network Tap ML-TAP-2810 – Mylinking

Short Description:

Product Detail

Product Tags

Feedback (2)

The key to our success is "Good Product Quality, Reasonable Value and Efficient Service" for Motorcycle Bluetooth , Sdn Network Packet Broker , Splitter Tap , We warmly welcome customers from all over the world for any kind of cooperation with us to build a mutual benefit future. We are devoting ourselves wholeheartedly to offer customers the best service.

Manufacturer of Data Center Tap - Mylinking™ Network Tap ML-TAP-2810 – Mylinking Detail:

1- Overviews

A full visual control of Data Acquisition device(4*10GE SFP+ plus 24*GE SFP ports)
A full Data Scheduling Management of nework traffic capture and monitoring device(duplex Rx/Tx processing)
A full packet pre-processing and re-distribution device(bidirectional bandwidth 64Gbps)
Supported traffic collection & reception of link data from different network element locations
Supported traffic collection & reception of link data from different switch routing nodes
Supported raw packet captured, identified, analyzed, statistically summarized and marked
Supported packet filtering matches, including policy filtering based on quintuple (source IP address, destination IP address, source port, destination port, and protocol number), packet characteristics, and deep identification of packet content
Supported raw packet output for monitoring equipment of Data Packet Analysis, Protocol Analysis, Signaling Analysis, Security Analysis, Risk Management and other traffic reqirement.

product-description1

ML-TAP-2810

2- System Block Diagram

product-description2

3- Operating Principle

product-description3

The Network Traffic Tap embedded traffic guidance function, which is mainly coordinated by the built-in TCAM traffic identification policy engine, traffic control guidance engine, port media transceiver module (MAC+PHY), and high-speed backplane switch bus. The port media transceiver module collects the traffic and enters the traffic identification matching engine to perform traffic identification matching. The identification matching engine performs high-speed hardware parallel matching based on the TCAM three-state content addressing memory, which can complete high-speed traffic identification of line speed traffic. After traffic identification, the traffic will enter the high-speed switching bus for traffic forwarding, replication, aggregation, or shunting. The traffic control guide engine can accurately control the traffic output interface of each type of traffic identification frame.

4- Intelligent Traffic Processing Abilities

6- Specifications

Mylinking™ Network TapNPB/TAP Functional Parameters
Network Interface	GE ports	24*GE SFP slots
Network Interface	10GE ports	4*10GE SFP+ slots
Deployment mode	SPAN monitoring input	support
Deployment mode	In-line mode	support
	Total QTYs interface	28
	Traffic replication / aggregation / distribution	support
	Link QTYs supporting Mirror replication / aggregation	1 -> N link traffic replication (N <28) N-> 1 link traffic aggregation (N <28) G Group(M-> N Link) traffic replication and aggregation [G * (M + N) <28]
Functions	Distribution based on traffic identification	support
	Distribution based on IP / protocol / port Five tuple traffic identification	support
	Distribution strategy based on protocol header the key labeled traffic identifies	support
	Strategic distribution based on deep message content identification	support
	Support Ethernet encapsulation independence	support
	CONSOLE Network Management	support
	IP/WEB Network Management	support
	SNMP V1/V2C Network Management	support
	TELNET/SSH Network Management	support
	SYSLOG Protocol	support
	User authentication function	Password authentication based on user name
Electric(1+1 Redundant Power System-RPS)	Rated supply voltage	AC110-240V/DC-48V [Optional]
	Rated power frequency	AC-50HZ
	Rated input current	AC-3A / DC-10A
	Rated power function	150W(2401: 100W )
Environment	Operating Temperature	0－50℃
	Storage Temperature	-20-70℃
	Operating Humidity	10%-95%, Non-condensing
User Configuration	Console Configuration	RS232 Interface, 9600,8,N,1
User Configuration	Password authentication	support
Rack Height	Rack space (U)	1U 460mm45mm440mm

7- Order Information

ML-TAP-2401 mylinking™ Network Tap 24*GE SFP ports
ML-TAP-1410 mylinking™ Network Tap 12*GE SFP ports plus 2*10GE SFP+ ports
ML-TAP-2610 mylinking™ Network Tap 24*GE SFP ports plus 2*10GE SFP+ ports
ML-TAP-2810 mylinking™ Network Tap 24*GE SFP ports plus 4*10GE SFP+ ports

Product detail pictures:

Related Product Guide:

Our intention is usually to satisfy our buyers by offering golden provider, great rate and good quality for Manufacturer of Data Center Tap - Mylinking™ Network Tap ML-TAP-2810 – Mylinking , The product will supply to all over the world, such as: Brasilia, Australia, Spain, All the imported machines effectively control and guarantee the machining precision for the products. Besides, we have a group of high-quality management personnels and professionals, who make the high-quality products and have the ability to develop new products to expand our market home and abroad. We sincerely expect customers come for a blooming business for both of us.

Balancing Network Tap