Renewable Design for Tap Replicator - Mylinking™ Network Tap ML-TAP-2810 – Mylinking

Short Description:

Product Detail

Product Tags

Feedback (2)

With our rich working experience and thoughtful companies, we have now been recognized as being a trustworthy supplier for a lot of global potential buyers for 10gb Network Tap , Pppoe Header Stripping , Network Packet Analysis , Our products are strictly inspected before exporting , So we gain a good reputation all over the world. We looking forward to cooperation with you in the future.

Renewable Design for Tap Replicator - Mylinking™ Network Tap ML-TAP-2810 – Mylinking Detail:

1- Overviews

A full visual control of Data Acquisition device(4*10GE SFP+ plus 24*GE SFP ports)
A full Data Scheduling Management of nework traffic capture and monitoring device(duplex Rx/Tx processing)
A full packet pre-processing and re-distribution device(bidirectional bandwidth 64Gbps)
Supported traffic collection & reception of link data from different network element locations
Supported traffic collection & reception of link data from different switch routing nodes
Supported raw packet captured, identified, analyzed, statistically summarized and marked
Supported packet filtering matches, including policy filtering based on quintuple (source IP address, destination IP address, source port, destination port, and protocol number), packet characteristics, and deep identification of packet content
Supported raw packet output for monitoring equipment of Data Packet Analysis, Protocol Analysis, Signaling Analysis, Security Analysis, Risk Management and other traffic reqirement.

product-description1

ML-TAP-2810

2- System Block Diagram

product-description2

3- Operating Principle

product-description3

The Network Traffic Tap embedded traffic guidance function, which is mainly coordinated by the built-in TCAM traffic identification policy engine, traffic control guidance engine, port media transceiver module (MAC+PHY), and high-speed backplane switch bus. The port media transceiver module collects the traffic and enters the traffic identification matching engine to perform traffic identification matching. The identification matching engine performs high-speed hardware parallel matching based on the TCAM three-state content addressing memory, which can complete high-speed traffic identification of line speed traffic. After traffic identification, the traffic will enter the high-speed switching bus for traffic forwarding, replication, aggregation, or shunting. The traffic control guide engine can accurately control the traffic output interface of each type of traffic identification frame.

4- Intelligent Traffic Processing Abilities

6- Specifications

Mylinking™ Network TapNPB/TAP Functional Parameters
Network Interface	GE ports	24*GE SFP slots
Network Interface	10GE ports	4*10GE SFP+ slots
Deployment mode	SPAN monitoring input	support
Deployment mode	In-line mode	support
	Total QTYs interface	28
	Traffic replication / aggregation / distribution	support
	Link QTYs supporting Mirror replication / aggregation	1 -> N link traffic replication (N <28) N-> 1 link traffic aggregation (N <28) G Group(M-> N Link) traffic replication and aggregation [G * (M + N) <28]
Functions	Distribution based on traffic identification	support
	Distribution based on IP / protocol / port Five tuple traffic identification	support
	Distribution strategy based on protocol header the key labeled traffic identifies	support
	Strategic distribution based on deep message content identification	support
	Support Ethernet encapsulation independence	support
	CONSOLE Network Management	support
	IP/WEB Network Management	support
	SNMP V1/V2C Network Management	support
	TELNET/SSH Network Management	support
	SYSLOG Protocol	support
	User authentication function	Password authentication based on user name
Electric(1+1 Redundant Power System-RPS)	Rated supply voltage	AC110-240V/DC-48V [Optional]
	Rated power frequency	AC-50HZ
	Rated input current	AC-3A / DC-10A
	Rated power function	150W(2401: 100W )
Environment	Operating Temperature	0－50℃
	Storage Temperature	-20-70℃
	Operating Humidity	10%-95%, Non-condensing
User Configuration	Console Configuration	RS232 Interface, 9600,8,N,1
User Configuration	Password authentication	support
Rack Height	Rack space (U)	1U 460mm45mm440mm

7- Order Information

ML-TAP-2401 mylinking™ Network Tap 24*GE SFP ports
ML-TAP-1410 mylinking™ Network Tap 12*GE SFP ports plus 2*10GE SFP+ ports
ML-TAP-2610 mylinking™ Network Tap 24*GE SFP ports plus 2*10GE SFP+ ports
ML-TAP-2810 mylinking™ Network Tap 24*GE SFP ports plus 4*10GE SFP+ ports

Product detail pictures:

Related Product Guide:

We provide good power in high-quality and progress,merchandising,revenue and internet marketing and operation for Renewable Design for Tap Replicator - Mylinking™ Network Tap ML-TAP-2810 – Mylinking , The product will supply to all over the world, such as: Ukraine, kazan, Burundi, "Good quality, Good service " is always our tenet and credo. We take every effort to control the quality, package, labels etc and our QC will check every detail during producing and before shipment. We are willing to establish long business relationship with those who seek the high quality products and good service. We have set up a wide sales network across European countries, North of America, South of America, Middle East, Africa, East Asia countries.Please contact us now, you will find our professional experience and high quality grades will contribute to your business.

Copper Tap Test